The HOLDEN HZ KINGSWOOD PANEL VAN novelty plate shows the car that was produced by Holden in Australia from October 1977 – 1980 in a variety of equipment levels and in several different body styles. It was also assembled in New Zealand. Wikipedia tells us that the Holden HZ received minor updates to the exterior over the HX series, and saw the introduction of what Holden termed “Radial Tuned Suspension” (RTS) across all models. RTS made significant changes to the suspension of the car, greatly improving the handling finesse, while at the same time not compromising ride quality. Modern Motor magazine described the HZ as “a great handler spoiled by the car” in a comparison against the BMW 528i, contrasted as “a great car spoiled by the handling”. In this series, the base specification Belmont was deleted and the new Kingswood SL became the base luxury level for sedans and wagons, with a lower specification Kingswood sedan and wagon only offered as a delete option on the Kingswood SL. During the course of the HZ series, equipment levels were upgraded in 1978 effectively to match improvements in the opposition Ford Falcon range, but the life of the full W size Holden looked set to end following Holden’s release of the VB Commodore in November 1978. After 1980, W sized Holden passenger cars were cancelled—replaced by the downsized Commodore. The Kingswood luxury level lived on until 1985 on the WB Holden utility but the end of HZ saw the end of the Holden Premier alongside both the GTS and Sandman which were both deleted prior to the end of the HZ series.
The Holden HZ was offered in four sedan and three station wagon models, marketed as follows:
Holden Kingswood Sedan / Holden Kingswood Wagon / Holden Kingswood SL Sedan / Holden Kingswood SL Wagon / Holden Premier Sedan / Holden Premier Wagon / Holden GTS /
It was also available in two coupe utility, two panel van and one cab chassis model, marketed as follows:
Holden Ute / Holden Kingswood Ute / Holden Van / Holden Kingswood Van / Holden One Tonner (cab chassis)
There were two special vehicle packages also available based upon commercial vehicles: Holden Sandman Ute and Holden Sandman Van
This plate comes standard as completely flat and non-embossed but for a little more cost we are able to give it a pressed out embossed border, so you have a choice. Please select your preference from the drop down menu.
These novelty number plates are made from high quality aluminium and the artwork applied by a dye sublimation process with a lovely gloss finish. They measure 37 x 13 cm, exactly the same as the traditional fully embossed type of plate and look just like our other Aussie made novelty number plates; even the mounting holes are in exactly the same positions, so they can easily be hung on display indoors or outdoors. One great advantage the flat non-embossed version is that owing to the absence of embossed border, and being just under 1 mm thick, it’s quite flexible and will flex about 10 cm from the centre, so can be mounted on curved surfaces.
Each embossed rim style plate is sealed in a clear plastic sleeve, and each flat non-embossed plate is shrink-sealed in plastic film, so both types are ready for retail display, plus we offer the option of fixing them to a cardboard display card, so they can then be hung and displayed on the same display racks that are used for the other Aussie size plates we sell. To see what the display card looks like please click here
For protection during delivery we use extra packing materials to ensure they arrive in tip-top condition
If you would like plates made to your own design, we can easily do this for you. Virtually anything you want can be created with our modern digital equipment. The key is good art, and we can do
ANY GRAPHIC! ANY DESIGN! ANY COLOUR!
For more details on creating a plate to your design please click here
Important note about images we provide : Just as we sometimes see that “pricing is subject to change without notice”, so too are “designs subject to change without notice”. In 99.99% of cases, what you see on Dixie’s website or brochure is what you get. However, there are the odd times when designs have changed in some small way (eg: maybe a logo moves to a different location on the item, or the colour changes). Sometimes this information doesn’t always trickle down until the new designs are manufactured and shipped to Dixie. We hope this is helpful and understandable.